塑料模具设计技术英语

Chapter l General mould construction基本模具结构
1.1 Basic Terminology基本术语
1.2 Integer cavity and core plates整体式型腔和型芯板
1.3 Use of local inserts局部镶块的使用
1.4 Inserts for cavity and core型腔和型芯镶块
1.5 Types of guide pillars and guide bushes导柱和导套的形式
1.6 Sprue bush浇口套
1.7 Register rin9定位圈
Chapter 2 Parting surface分型面
2.1 Flat parting surface平面分型面
2.2 Non—flat parting surface非平面分型面
2.3 Relief of parting surfaces分型面的释放
2.4 Ventin9排气
Chapter 3 Ejection system顶料系统
3.1 Removing the moldin9塑件的取出
3.2 In—line Ejector grid内嵌顶料架
3.3 Ejector plate assembly顶料板组合
3.4 Ejector plate顶料板
3.5 Retaining plate and stop pins固定板和挡钉
3.6 Ejector plate assembly returns systems顶料板回程机构
3.7 Ejection Techniques顶料方法
3.8 Pin ejection顶杆顶料
3.9 Stepped ejector pins阶梯形顶杆
3.10 Sleeve ejection顶管顶料
3.11 Stripper plate ejection顶板顶料
3.12 Sprue pullers主流道拉料杆
3.13 The B sprue pullers B型主流道拉料杆
Chapter 4 Feed system浇注系统
4.1 Runner分流道
4.2 Runner cross section shape分流道截面形状
4.3 Runner size分流道尺寸
4.4 Runner layout分流道布置
4.5 Gates浇口
4.6 Positioning of gate浇口的位置
4.7 Sprue gate主流道型浇口
4.8 Rectangular edge gate矩形浇口
4.9 Round edge gate圆浇口
4.10 0verlap gate叠合式浇口
4.11 Fan gate扇形浇口
4.12 Tab gate护耳式浇口
4.13 Diaphragm gate叠合式膜状浇口
4.14 Ring gate and film gate环形浇口和膜状浇口
4.15 Pin gate点浇口
4.16 Subsurface gate潜伏式浇口
4.17 Winkle gate螺肉形浇口
Chapter 5 Mould temperature control模具温度控制
5.1 Mould coolin9模具冷却
5.2 The cooling of shallow integer type cavity整体式浅腔的冷却
5.3 The cooling of deep integer type cavities整体式深腔的冷却
5.4 Cooling integer type core plate整体式型芯板的冷却
5.5 Cooling insert bolster镶块板的冷却
5.6 Cooling rectangular cavity inserts矩形型腔镶块的冷却
5.7 Cooling circular cavity inserts圆形型腔镶块的冷却
5.8 Cooling shallow core inserts浅型芯镶块的冷却
5.9 Cooling deep core inserts深型芯镶块的冷却
5.10 The helical cooling channel design of deep core insert深型芯镶块的螺旋冷却槽设计
5.11 Baffled hole system design of deep core insert深型芯镶块带隔板孔的冷却系统
5.12 Heat rods of deep core insert coolin9深型芯冷却用的热杆
5.13 Heat pipe of deep core insert coolin9深型芯冷却用的热管
5.14 Cooling of valve ejectors and sprue bush阀形顶杆和主流道衬套等的冷却
……
Chapter 6 Standard parts systems模具标准件系统
Chapter 7 Purchasing order模具采购合同
Chapter 8 Mould design technology documents模具设计技术文本
References参考文献